Our Products

PHOTOVOLTAIC EQUIPMENT

FAC3: Insulation Monitoring Device with Automatic Reset

FAC3: INSULATION MONITORING DEVICE WITH AUTOMATIC RESET

The FAC3 detects insulation failure to ground, discriminating whether the failure is positive or negative. Reset function incorporated with selectable time. It has two output contacts, potential-free changeover. Suitable for application in photovoltaic installations up to 1000 Vdc.

 MORE INFORMATION
FAC/055 Insulation monitor for batterie's instalations

FAC/055 INSULATION MONITOR FOR BATTERIE'S INSTALATIONS

Detected in installations of 24 VDC or 48 VDC, lack of insulation of the leads (+) or (-) to ground. The same model is valid for both installations (24/48 VDC)

 MORE INFORMATION
FAT Monitor that detects earth leakage in photovoltaic installations with a grounded pole

FAT MONITOR THAT DETECTS EARTH LEAKAGE IN PHOTOVOLTAIC INSTALLATIONS WITH A GROUNDED POLE

 

This FAT equipment measures the flow of current to ground and when it reaches a certain level, it acts, and the union to ground will be open. That way if someone accidentally touches the pole is not connected to ground, it opens the circuit.

 

 MORE INFORMATION
FAT-H: Monitoring earth leakage in photovoltaic installations in which one pole is grounded

FAT-H: MONITORING EARTH LEAKAGE IN PHOTOVOLTAIC INSTALLATIONS IN WHICH ONE POLE IS GROUNDED

This FAT-H device measures the current to ground and when it reaches a certain level acts giving orders via a  contact potential-free. This contact may be used to disconnect the connection to ground, stopping the inverter voltage or short-circuit the panels, it depend of the associated equipment used.
To short-circuit voltage panels, you can use a continous switch ( NIPS-300,  NINFAC , NMI, ...).

 MORE INFORMATION
The MED - Measure the voltage and current of a photovoltaic. With comunications.RS485

THE MED - MEASURE THE VOLTAGE AND CURRENT OF A PHOTOVOLTAIC. WITH COMUNICATIONS.RS485

The MED allows remote monitoring operation of the installation. Use the MODBUS-RTU protocol.

 MORE INFORMATION
MED5: Measurement of currents in FotoVivo Inst. with interface RS-485

MED5: MEASUREMENT OF CURRENTS IN FOTOVIVO INST. WITH INTERFACE RS-485

The MED5 is a device designed to measure the intensities of up to five branches of a photovoltaic system, sending this information to the control center via communications.

 MORE INFORMATION
PRMEDC: DC measuring transducers

PRMEDC: DC MEASURING TRANSDUCERS

In photovoltaic systems, convert levels of input voltage or current levels to output current type (4-20mA, 0-5mA, 0-20mA). The input, output and auxiliary supply are galvanically isolated from each other

 MORE INFORMATION
BSF5: Tracker Fault Detector

BSF5: TRACKER FAULT DETECTOR

The BSF5 is used in photovoltaic installations containing several trackers or strings. Together with the NINFAC DC Breakers, it determines which tracker has an isolation fault once it has been detected by the installation's Isolation Monitoring Device.

 MORE INFORMATION
NINFAC - Breaker DC

NINFAC - BREAKER DC

Upon receiving the order from a monitor of isolation (for example, FAC3 / I), the NINFAC disconnects the inverter from solar panels, then power panels shorted and grounded.
NMI - Integrated Module: Monitor Isolation and breaker

NMI - INTEGRATED MODULE: MONITOR ISOLATION AND BREAKER

Included in the same set a Monitor of Isolation FAC3 and Continuous Switch NINFAC
NIPS- DC Breaker 300A

NIPS- DC BREAKER 300A

In the event of insulation failure, the NIPS disconnects the PV panels to the inverter, and shorted it to earth.

 MORE INFORMATION
FACV INSULATION MONITORING AC

FACV INSULATION MONITORING AC

The FACV monitors the insulation resistance AC power circuits unearthed (IT systems) from 0 to 320 AC.
The assistant allows independent power monitor the system without tension.

 MORE INFORMATION
MED6I1V Measure the voltage and current

MED6I1V MEASURE THE VOLTAGE AND CURRENT

Equipment for measuring up to 6 intensities and 1 DC voltage of 1,000 V. The current measurement is done through hall effect module external to the equipment, the range is 25 to 800 amperes.
Option is also manufactured with 5 digital inputs (logic), potential-free, to send to master the status of other environmental parameters and an input for temperature measurement PTC100Equipment for measuring up to 6 intensities and 1 DC voltage of 1,000 V. The current measurement is done through hall effect module external to the equipment, the range is 25 to 800 amperes.

 
lastnext